The Road Vehicles (Construction and Use) (Amendment) Regulations 2025
The Road Vehicles (Construction and Use) (Amendment) Regulations 2025 amend the 1986 Regulations to permit road use of hydrogen-fuelled agricultural vehicles, engineering plant, works trucks, and category T tractors.
The amendments introduce new safety requirements for hydrogen fuel systems, including stipulations for fuelling receptacles, pressure relief devices, leak prevention, and driver warnings.
These requirements align with UNECE regulations and aim to balance enabling the use of hydrogen technology with ensuring public and environmental safety.
Arguments For
Increased use of hydrogen fuel technology: The regulations facilitate the adoption of cleaner, more sustainable hydrogen fuel technology in specified vehicle types.
Economic benefits: Supporting the development and use of hydrogen-powered vehicles can stimulate economic growth in related industries and create new job opportunities.
Environmental benefits: Hydrogen fuel offers the potential for reduced greenhouse gas emissions compared to traditional fossil fuels, thus promoting better environmental protection.
Legal basis: The regulations are made under the powers conferred by section 41(1) and (5) of the Road Traffic Act 1988, providing a clear legal foundation for the amendments.
Alignment with international standards: The regulations incorporate relevant UNECE regulations (134, 134.01, 134.02), ensuring harmonization with international standards for hydrogen vehicle safety.
Arguments Against
Safety concerns: The use of hydrogen fuel presents potential safety risks requiring stringent regulations and careful implementation to mitigate hazards, such as leaks and explosions.
Infrastructure limitations: Widespread adoption of hydrogen fuel vehicles needs substantial investment in new refuelling infrastructure before being practical for many users.
Cost implications: The initial cost of hydrogen-fuelled vehicles might be higher than those using conventional fuels, potentially hindering public adoption unless heavily subsidised.
Potential unintended consequences: Changes to vehicle regulations may introduce unintended consequences that could impact other aspects of road transport or related industries.
Implementation challenges: Effective enforcement of new safety standards outlined in the regulations and effective oversight of compliance could pose considerable challenges.
The Secretary of State makes these Regulations in exercise of the powers conferred by section 41(1) and (5) of the Road Traffic Act 19881.The Secretary of State has consulted with representative organisations in accordance with section 195(2) of that Act.
The Secretary of State created these Regulations using the authority granted by Section 41(1) and (5) of the Road Traffic Act 1988.
Following legal requirements, consultations were held with relevant organizations per Section 195(2) of the same Act.
These Regulations may be cited as the Road Vehicles (Construction and Use) (Amendment) Regulations 2025 and come into force on 29th April 2025. These Regulations extend to England and Wales and Scotland.
These regulations are officially titled 'Road Vehicles (Construction and Use) (Amendment) Regulations 2025' and took effect on April 29th, 2025.
They apply to England, Wales, and Scotland.
The Road Vehicles (Construction and Use) Regulations 19862 are amended as follows.In regulation 94, for paragraph (2A) substitute—
“(2A) No person may use, or cause or permit to be used, on a road a vehicle that is fitted with a hydrogen fuel system or a natural gas fuel system unless—(a) that vehicle has been approved under the Road Vehicles (Approval) Regulations 20203 for that system at the time of registration, or(b) that vehicle meets the requirements in paragraph (2B) or (2C). (2B) A vehicle meets the requirements of this paragraph if it—(a) is designed and constructed, and not merely adapted, to be fuelled by hydrogen,(b) complies with the Pressure Equipment (Safety) Regulations 20164,(c) complies with Schedule 5A, and(d) is one of the following vehicles—(i) an agricultural motor vehicle;(ii) engineering plant;(iii) a works truck. (2C) A vehicle meets the requirements of this paragraph if it—(a) is designed and constructed, and not merely adapted, to be fuelled by hydrogen,(b) complies with Parts I and II of ECE Regulation 134, 134.01 or 134.025,(c) complies with Schedule 5A, and(d) is a category T tractor.”
The 1986 Road Vehicles (Construction and Use) Regulations are modified.
Specifically, Regulation 94, paragraph (2A), is replaced.
The new (2A) states that using a vehicle with a hydrogen or natural gas fuel system on a road requires either approval under the 2020 Road Vehicles (Approval) Regulations at registration or meeting the criteria in the new paragraphs (2B) and (2C).
Paragraph (2B) details requirements for agricultural vehicles, engineering plant, and works trucks fueled by hydrogen; and paragraph (2C) for category T tractors fueled by hydrogen, specifying design, construction, and compliance with safety regulations.
In Schedule 2 (Community Directives and ECE Regulations), in table 2 (ECE Regulations), after the entry relating to item 29, insert—
“30
134
134
15.6.2015
Hydrogen and fuel cell vehicles
-
-
-
31
134.01
134
15.6.2015
Hydrogen and fuel cell vehicles
7.1.2022
-
-
32
134.02
134
15.6.2015
Hydrogen and fuel cell vehicles
15.6.2024
-
-”.
Schedule 2, Table 2 (ECE Regulations), is updated.
Three new entries (30, 31, and 32) are added, referencing UNECE Regulations 134, 134.01, and 134.02, respectively, which cover hydrogen and fuel cell vehicles.
These additions formally incorporate these international safety standards into UK legislation.
After Schedule 5 (Gas Systems), insert—
“Schedule 5A HYDROGEN FUELLED MACHINERY (see regulation 94)Definitions1. (1) In this Schedule—“hydrogen-fuelled vehicle” means a vehicle that is specified in regulation 94(2B) or (2C) and that uses compressed gaseous hydrogen as a fuel to propel the vehicle.(2) Other expressions that are used in this Schedule and that are defined in ECE Regulation 134.02 have the same meaning in this Schedule as they have in ECE Regulation 134.02.Fuelling receptacle2. (1) A fuelling receptacle must be fitted to a hydrogen-fuelled vehicle.(2) A fuelling receptacle fitted to a hydrogen-fuelled vehicle must—(a) prevent reverse flow of gaseous hydrogen fuel to the atmosphere;(b) have a label affixed close to the fuelling receptacle that shows—(i) the fuel type,(ii) the maximum fuelling pressure,(iii) the nominal working pressure, and(iv) the date of removal from service of each container;(c) be mounted on the hydrogen-fuelled vehicle to ensure positive locking of the fuel nozzle;(d) be protected from tampering and ingress of dirt and water.(3) A fuelling receptacle fitted to a hydrogen-fuelled vehicle must not—(a) be mounted within the external energy absorbing elements of the hydrogen-fuelled vehicle;(b) be installed so that access for refilling is in the passenger compartment or an unventilated compartment.Overpressure protection for the low pressure system3. (1) The compressed hydrogen storage system downstream of a pressure regulator must be protected against overpressure.(2) Use of an overpressure protection device, including a pressure relief device, is sufficient to meet the requirement in sub-paragraph (1).(3) The set pressure of an overpressure protection device must be lower than or equal to the maximum allowable working pressure for the appropriate section of the compressed hydrogen storage system.Discharge from thermally-activated pressure relief devices4. (1) Compressed hydrogen gas discharge from a thermally-activated pressure relief device of a compressed hydrogen storage system must not be directed—(a) into enclosed or semi-enclosed spaces;(b) into or towards any vehicle wheel housing;(c) towards each container;(d) forward from the hydrogen-fuelled vehicle, or horizontally (parallel to the road) from the back or sides of the hydrogen-fuelled vehicle.(2) If a thermally-activated pressure relief device of a compressed hydrogen storage system has a vent line, the outlet of this vent line must be protected by a cap.Discharge from other pressure relief devices5. (1) The hydrogen gas discharge from other pressure relief devices that are not thermally-activated, including burst discs, must not be directed—(a) towards exposed electrical terminals, exposed electrical switches or other ignition sources;(b) into or towards the passenger compartment;(c) into or towards any vehicle wheel housing;(d) towards each container.(2) At the hydrogen-fuelled vehicle exhaust system’s point of discharge, the hydrogen concentration level must not exceed—(a) 4.0% average by volume during any moving three-second time interval during normal operation, including start-up and shut-down;(b) 8.0% at any time.(3) The test procedure that must be followed, for determining the hydrogen concentration level in sub-paragraph (2), is the compliance test for the vehicle exhaust system in paragraph 4 of Annex 5 to ECE Regulation 134.02.Protection against flammable conditions6. (1) Hydrogen leakage and permeation from the compressed hydrogen storage system must not directly vent into the passenger compartment, or into any enclosed or semi-enclosed spaces within the hydrogen-fuelled vehicle that contain unprotected ignition sources.(2) Any single failure downstream of the main hydrogen shut-off valve must not result in accumulations in levels of hydrogen concentration in the passenger compartment.(3) The requirement in sub-paragraph (2) is met if the hydrogen concentration in the passenger compartment does not exceed 1.0% by volume when tested in accordance with sub-paragraph (4).(4) The test procedure for determining levels of hydrogen concentration in sub-paragraph (2) is the test procedure for integrity of enclosed spaces and detection systems in paragraph 3.2 of Annex 5 to ECE Regulation 134.02.(5) If, during operation, the hydrogen concentration exceeds 3.0% by volume in the air in the enclosed or semi-enclosed spaces of the hydrogen-fuelled vehicle, a warning must be provided in accordance with paragraph 7.(6) If, during operation, the hydrogen concentration exceeds 4.0% by volume in the air in the enclosed or semi-enclosed spaces of the hydrogen-fuelled vehicle, the main shut-off valve must be closed to isolate the compressed hydrogen storage system.Signal warning to driver7. (1) A warning must be provided if the condition in paragraph 6(5) is met.(2) The warning must be given by a visual signal or display text and must—(a) be visible to the driver while the driver is in their designated seating position with their seat belt fastened;(b) be yellow in colour if the detection system malfunctions;(c) be red in colour if a single failure results in a hydrogen concentration exceeding 3.0% by volume in the air in the enclosed or semi-enclosed spaces of the hydrogen-fuelled vehicle;(d) when illuminated, be visible to the driver under both daylight and night time driving conditions;(e) remain illuminated if the ignition locking system is on the ‘On’ or ‘Run’ position, or if the propulsion system is activated, and—(i) hydrogen concentration exceeds 3.0% by volume in the air in the enclosed or semi-enclosed spaces of the hydrogen-fuelled vehicle, or(ii) a detection system malfunction exists.Fuel system leakage8. (1) The hydrogen fuelling line, including piping and joints, that is downstream of any shut-off valves to the fuel cell system or the engine must not leak.(2) Compliance with sub-paragraph (1) must be verified at nominal working pressure using the test procedure set out in paragraph 5 of Annex 5 to ECE Regulation 134.02.Additional installation requirements9. (1) Each container must be mounted in a position that is between two vertical planes that are located perpendicular to the centre line of the hydrogen-fuelled vehicle.(2) The two vertical planes referred to in sub-paragraph (1) must be located at least—(a) 200 mm rearward from the front edge of the hydrogen-fuelled vehicle, and(b) 200 mm forward of the rear edge of the hydrogen-fuelled vehicle.(3) Each container must be mounted in a position that is between the two vertical planes that are parallel to the centre line of the hydrogen-fuelled vehicle.(4) The two vertical planes referred to in sub-paragraph (3) must be located at least 200 mm inside from the outermost edges of the hydrogen-fuelled vehicle in the proximity of each container.(5) A hydrogen-fuelled vehicle that does not comply with sub-paragraphs (3) and (4) may still be considered compliant with the requirements of this paragraph if it has passed the lateral impact test specified in paragraph 7.2.4.3 of ECE Regulation 134.02.(6) For the purposes of sub-paragraph (5)—(a) the lateral impact test must be conducted by a Technical Service that is responsible for conducting approval tests and that has been communicated to the United Nations secretariat in accordance with paragraph 12 of ECE Regulation 134.02;(b) the requirement for the compressed hydrogen storage system to be filled with hydrogen or helium in paragraph 1 of Part 1 or paragraph 1 of Part 2 of Annex 8 to ECE Regulation 134.02 does not need to be met if the following criteria are met instead—(i) the compressed hydrogen storage system is empty or filled with an inert gas to a pressure below or equal to 20 bar for the purposes of the lateral impact test,(ii) after the lateral impact test, any inert gas is removed and the compressed hydrogen storage system is repressurised to nominal working pressure with hydrogen or helium, before the Technical Service tests hydrogen gas leakage in accordance with paragraph 7.2.1 of ECE Regulation 134.02, and(iii) for the purposes of sub-paragraph (ii), the time interval for starting measurement of hydrogen gas leakage is after the compressed hydrogen storage system has been repressurised with hydrogen or helium;(c) demonstration of compliance through the calculation method described in paragraph 7.2.4.3 of ECE Regulation 134.02 is not permitted as an alternative to the lateral impact test.”
A new Schedule 5A, "Hydrogen Fuelled Machinery," is added.
This schedule establishes detailed safety requirements for hydrogen-fuelled vehicles, including specifications for fuelling receptacles (preventing leaks and clear labeling), overpressure protection, safe discharge of pressure relief valves, protection against flammable conditions (leak prevention measures and driver warnings), and precise installation requirements for hydrogen containers.
These requirements reference and incorporate test procedures outlined in UNECE Regulation 134.02.
Signed by authority of the Secretary of State for TransportLilian GreenwoodParliamentary Under Secretary of StateDepartment for TransportAt 9:24 a.m. on 7th April 2025
These regulations were signed by Lilian Greenwood, Parliamentary Under Secretary of State for the Department for Transport, on April 7th, 2025.
These Regulations amend the Road Vehicles (Construction and Use) Regulations 1986 (“the 1986 Regulations”) to enable the road use of hydrogen-fuelled non-road mobile machinery and category T tractors.Regulation 94(2A) of the 1986 Regulations requires that, for vehicles fitted with a hydrogen or natural gas fuel system, the system must be approved under the Roads Vehicles (Approval) Regulations 2009 before it may be used.Regulation 2 of these Regulations creates a new exemption by amending regulation 94(2A) to enable the road use of hydrogen-fuelled vehicles that meet the requirements specified in new paragraphs (2B) and (2C).The requirements specified in new paragraph (2B) are that the vehicle must be an agricultural motor vehicle, engineering plant or a works truck, have been designed and constructed to be fuelled by hydrogen, and must comply with the Pressure Equipment (Safety) Regulations 2016 and the requirements in new Schedule 5A.The requirements specified in new paragraph (2C) are that the vehicle must be a category T tractor, have been designed and constructed to be fuelled by hydrogen, and must comply with Parts I and II of UN Regulation 134, 134.01 or 134.02 and the requirements in new Schedule 5A.New Schedule 5A sets out safety requirements for hydrogen-fuelled vehicles specified in regulation 94(2B) or (2C), including requirements relating to the fuelling receptacle, pressure relief devices, protection against flammable conditions, signal warnings to the driver, fuel system leakage and installation requirements.Regulation 2 of these Regulations also updates the reference to the Road Vehicles (Approval) Regulations 2009 to refer to the Road Vehicles (Approval) Regulations 2020 instead.UN Regulations are issued by the United Nations Economic Commission for Europe. Copies of UN Regulation 134, 134.01 and 134.02 may be obtained from the UNECE website: http://www.unece.org/trans/main/wp29/wp29regs.html. Hard copies may be obtained from the Department for Transport, Great Minster House, 33 Horseferry Road, London, SW1P 4DR.A full impact assessment has not been produced for this instrument as no significant impact on the private, voluntary or public sector is foreseen.An Explanatory Memorandum has been prepared and is available alongside this instrument at www.legislation.gov.uk, or from the Department for Transport, Great Minster House, 33 Horseferry Road, London, SW1P 4DR.
This explanatory note summarizes the changes made by the regulations.
It clarifies the purpose of the amendments to the 1986 regulations, which is to allow the use of hydrogen-fuelled non-road mobile machinery and category T tractors on roads, while ensuring public safety through stringent requirements on hydrogen fuel systems.
The note also explains the updated reference to the Road Vehicles (Approval) Regulations and provides information on obtaining copies of the UN Regulations referenced in document.